Käyttöopas Honeywell Verkkokortti Hc900 [156/228 Sivut]

Honeywell verkkokortti HC900

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

Removal and Replacement Procedures - Safety Considerations - PLAN AHEAD!

146 HC900 Hybrid Controller Installation and User Guide Revision 5

9/03

EXPLOSION HAZARD Class 1, Division 2 Installations

• SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.

EXPLOSION HAZARD Class 1, Division 2 Installations

• DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE

AREA IS KNOWN NOT TO BE HAZARDOUS.

Replacing the Power Supply

The power supply for the HC900 Hybrid Controller is available in two models and is used in the local

(controller) rack and in the remote (I/O expansion) racks(C50 CPU only), in 4-, 8-, and 12-module sizes.

This reduces required inventories of spare parts, and also simplifies removal and replacement procedures.

Removing the power supply from a rack will remove all DC voltages from the rack that powers the

Controller Module or Scanner Module, and from all I/O modules within the rack.

NOTE:

The power supply includes an internal fuse, rated at 5 amperes. This fuse is not replaceable in the field. If

desired, the user can provide an external fuse that has a current rating lower than that of the internal fuse.

Table 31 - Power Supply Replacement

Step Action

If the power supply to be replaced is powering a rack that is currently controlling a running

process, then:

Either:

- Ensure that powering the rack down will not have adverse consequences on any running process.

Or:

- Bring the process to a safe and orderly shutdown.

Using an external, user-supplied switch, disconnect the power supply from the source of site AC

power. Use a meter to ensure that power is off.

Depending on the type of wire lugs used, loosen or remove the three screws on the terminal board,

and remove the three wires from the terminal board.

NOTE: DO NOT remove the nut that secures the lug for the PE Ground wire

(green) to the grounding stake at the bottom of the rack.

At the top and bottom of the module, loosen the captured screws that secure the module in the

rack, and remove the power supply from the rack.

6. Place the new power supply in the rack.

7. Secure the lugs for AC wiring to the terminals on the new power supply.

• L1 (top terminal) - Black (USA) or Brown (Europe)

• L2 /N (middle terminal - White (USA) or Blue (Europe).

kasikirjatvaltameri.fi

Tietoa

Honeywell verkkokortti DCP552 Mark II

Honeywell verkkokortti 800-08115

Honeywell verkkokortti 50010425-501

Honeywell verkkokortti 9782 Series

Honeywell verkkokortti UMC800

Honeywell verkkokortti Q7230A

Honeywell verkkokortti HCE 60

Honeywell verkkokortti Q7330A

Honeywell verkkokortti N-ANN-RLY

Honeywell verkkokortti QS7800B

Honeywell verkkokortti PRO-2200

Honeywell verkkokortti UDC 6300

Honeywell verkkokortti Q7130A

Honeywell verkkokortti UDC2500

Honeywell verkkokortti Series 90

kasikirjatvaltameri.fi

Tietoa